1. Before powering on the frequency converter
First, check the ambient temperature and humidity. Excessive temperature can cause the inverter to overheat and alarm, and in severe cases, directly damage the inverter's power components and cause short circuits. Excessive humidity can cause internal short circuits within the inverter. During inverter operation, check the cooling system for proper functioning, such as whether the exhaust duct is unobstructed and whether the fan makes any abnormal noises. Inverters with higher protection ratings, such as IP20 and above, can generally be installed in an open environment. Inverters with IP20 or below should generally be cabinet-mounted. Therefore, the cooling effect of the inverter cabinet directly affects the normal operation of the inverter. The inverter's exhaust system, such as whether the fan rotates smoothly and whether there is dust or blockage at the air inlet, are areas that cannot be ignored in daily inspections. Also check whether the motor, reactor, and transformer are overheating or have any unusual odors; whether the inverter and motor make any abnormal noises; whether the current display on the inverter panel is too high or the current fluctuation is too large; and whether the output three-phase voltage and current are balanced.
II. Regular maintenance
Regularly check for dust inlets to ensure they are not blocked, and clean the air filter, cooling ducts, and internal dust monthly.
Regular inspections should be conducted annually: Check for loose screws, bolts, and connectors; check for short circuits in the input/output reactors' resistance to ground and between phases (normal resistance should be greater than tens of megohms); check for corrosion in conductors and insulators, and clean them immediately with alcohol if necessary; measure the stability of the output voltages of each circuit in the switching power supply, such as 5V, 12V, 15V, and 24V; check for arcing marks on the contactor contacts, and replace severely damaged contactors with new ones of the same model or larger capacity; confirm the correctness of the control voltage and perform sequential protection operation tests; confirm that there are no abnormalities in the protection display circuit; and confirm the balance of the output voltage when the frequency converter is running alone.
Perform routine maintenance and repair work on the frequency converter diligently. This mainly includes:
1. Regularly clean the inverter, paying particular attention to the rectifier cabinet, inverter cabinet, and control cabinet. If necessary, remove the circuit boards from the rectifier module, inverter module, and control cabinet for dust removal. Check if the inverter's lower air inlet and upper air outlet are clogged with dust. Inverters require a large airflow for heat dissipation, so after a certain period of operation, surface dust accumulation becomes severe, necessitating regular cleaning.
2. Open the front door of the inverter and disassemble the rear door. Carefully inspect the AC and DC busbars for deformation, corrosion, or oxidation. Check whether the screws at the busbar connections are loose, whether the screws at each installation and fixing point are loose, and whether the insulating sheets or insulating posts used for fixing are aged, cracked, or deformed. If any are found, replace them in time and tighten them again. Any deformed busbars must be corrected and reinstalled.
3. After dust removal from circuit boards and busbars, perform necessary anti-corrosion treatment and apply insulating varnish. For busbars showing partial discharge or arcing, remove burrs before further treatment. For insulation boards that have undergone insulation breakdown, remove the damaged parts, insulate the area around the damage with insulation boards of the appropriate insulation class, tighten them, and test the insulation before putting them into use.
4. Check whether the fans in the rectifier cabinet and inverter cabinet are operating and rotating normally. When the machine is stopped, rotate them by hand to check whether the bearings are stuck or making noise. Replace the bearings or repair them if necessary.
5. Conduct a comprehensive inspection of the input, rectification and inverter, and DC input fast fuses, and replace them promptly if any are found to be burnt out.
6. Check for leaks in the capacitors of the intermediate DC circuit, and inspect the casing for bulging, bubbling, or deformation. Also check for broken safety valves. If possible, test the capacitor's capacitance, leakage current, and withstand voltage. Replace any capacitors that do not meet the requirements. New capacitors or capacitors that have been idle for a long time must be passivated before replacement. The service life of filter capacitors is generally 5 years. For capacitors that have been used for more than 5 years and whose capacitance, leakage current, and withstand voltage significantly deviate from the testing standards, partial or complete replacement should be considered.
7. Use a multimeter to perform electrical tests on the diodes and GTOs in the rectifier and inverter sections, measure their forward and reverse resistance values, and carefully record the results in a pre-prepared table. Check whether the resistance values between each electrode are normal and whether the consistency of devices of the same model is good. Replace them if necessary.
8. Inspect the main contactors and other auxiliary contactors in the A1 and A2 incoming line cabinets. Carefully observe whether there is arcing, burrs, surface oxidation, or unevenness on the moving and stationary contacts of each contactor. If such problems are found, the corresponding moving and stationary contacts should be replaced to ensure safe and reliable contact.
9. Carefully inspect the terminal blocks for aging or loosening, for any hidden short circuits, for secure connections of all wires, for any damage to the wire sheaths, and for the secure insertion and insertion of all circuit board connectors. Verify the reliability of the main power supply connections, for any signs of overheating or oxidation at the connections, and for proper grounding.
10. Check for any abnormal noises, vibrations, or burnt smells from the reactor.
In addition, if conditions permit, the filtered DC waveform, inverter output waveform, and input power supply harmonic components can be measured.
III. Replacement of Spare Parts
Inverters consist of various components, some of which gradually degrade in performance and age after prolonged use. This is a major cause of inverter failure. To ensure the long-term normal operation of the equipment, the following components should be replaced periodically:
1. Cooling fan
The power module of a frequency converter is a high-heat-generating component, and the heat generated during continuous operation must be dissipated promptly. The lifespan of a typical fan is approximately 10-40 hours. Based on continuous operation of the frequency converter, the fan should be replaced every 2-3 years. Direct-cooling fans come in two-wire and three-wire versions. For two-wire fans, one wire is positive and the other is negative; ensure correct connection during replacement. Three-wire fans have a detection wire in addition to the positive and negative terminals; exercise extreme care during replacement to avoid triggering an overheating alarm on the frequency converter. AC fans are generally available in 220V and 380V versions; ensure the voltage rating is correct during replacement.
2. Filter capacitor
Intermediate DC circuit filter capacitor: Also known as an electrolytic capacitor, its main function is to smooth DC voltage and absorb low-frequency harmonics in DC. The heat generated by its continuous operation, combined with the heat generated by the frequency converter itself, accelerates the drying of its electrolyte, directly affecting its capacitance. Under normal circumstances, the capacitor's lifespan is about 5 years. It is recommended to check the capacitor's capacitance annually; generally, if its capacitance decreases by more than 20%, it should be replaced with a new filter capacitor.
Disclaimer: This article is a reprint. If it involves copyright issues, please contact us promptly for deletion (QQ: 2737591964). We apologize for any inconvenience.
